Whatever nonsense from here,
use the same imagination in on with other control systems👌!
Using a vehicle’s combustion engine for example!
There are so many sensors actuators,
obviously going to, from the ECU🤷♂️!
When You dismantle (open) the ECU,
You wonder where these sensors actuators’ wires are ending in the ECU🤔?!
By the way, because we’re writing loads of ‘ujinga’,
if You’re not fond of reading our rubbish,
just..
CLICK HERE 🤷♀️
..for briefer, Electronic Components‘ nonsense😜!
We compile Electronic Components‘ rubbish HERE🚽!
Click HERE to download nonsense😂🤣!
Sasa, all these sensors actuators to from the ECU🤔?
Remember, our ZAMBIA train🤔?
That nonsense was about a
microController 🥂 microPocessor
If You wish to what how it was,
🧻Click HERE 🚽
How we were able to..
..make train (S), to automatically, move while stopping at different stations, Solwezi, Chingola, Kitwe, Ndola, Kabwe, Lusaka, upto Livingstone, automatically😎!
Remember We were imagining😂🤣!
That nonsense was about a
microController 🥂 microPocessor
If You wish to what how it was,
🧻 Click HERE 🚽
Imagine these sensors like the activities that happened automatically when a train detected a train station🧐!
As soon the detector (R) detected (K) (train starion)👌!
Activity one📌
Power to one motor was cut, to slow down the train!
Activity two📌
Power to speakers, to announce🔊 arrival to station!
Activity Three📌
Cut Power to other second motor, to stop the train!
Activity four📌
Power to Door motors, to open the doors!
😂😜Long story, shorter,
So many activities done by one microController (C1)!
So many activities sequentially happening in logical order, or in a recurrent pattern, 1,2,3,etc!
The train’s function of moving and stopping and opening doors, all controlled by one chip (C1) microController!
microController(C1) listens to sensor(S1), then sensor (S2), (S2), (S3), etc!
There are preset values, ranges, that each sensor must report with-in,
otherwise fault code!
microController (C2 & C3)🤔?
Remember🤔!
On our ZAMBIA train, chip (C1) was responsible for the function of moving & stopping the train!
Chip (C2) was for function of watching out for other trains!
Chip (C3) was to detect if there are, or no, passengers so the train doesn’t stop!
Then chip (P) the microProcessor listened to all the functions (C1, C2, C3), should there be any discrepancies, nonsense is sorted depending!
Coming back to our engine..
A combustion Engine needs Air + Fuel + Ignition
So,
Chip (C2)works on the Ignition Control function!
Chip (C3) works on the Fuel Control function!
Chip (C4) works on the Air Control function!
Chip (C1)listens to Engine Management sensors!
The microProcessor (P) listens to microController (C1) so as to process on what ‘ujinga’ the microControllers (C2, C3, C4) should do🤷♂️!We pile some Control Systems‘ rubbish,
sensors, ECU, actuators
click HERE
Information with how they work, how they are made, how to test for whatever parameters,
..including repair or wire-hacks to deactivate sh*t🤐!
We piled some Control Systems’ rubbish,
sensors, ECU, actuators
click HERE
Information with how they work, how they are made, how to test for whatever parameters,
..including repair or wire-hacks to deactivate sh*t🤐!
You may want watch this rubbish Video🤷♂️!
By the way, because we’re writing loads of ‘ujinga’,
if You’re not fond of reading our rubbish,
just..
CLICK HERE 🤷♀️
..for briefer, Electronic Components‘ nonsense😜!We compile Electronic Components‘ rubbish HERE🚽!Click HERE to download nonsense😂🤣!
May be whatever is causing You believe MUST do some nonsense to the vehicle, is some minor external problem with the sensors or actuators🤷♂️!
So, this ujanja is how to check, verify all the control electronics in the vehicle, are in proper order!
click here
👇
IMMO OFF files 
☝☝
click
These files to disable immobilizer system so the ecu accepts any random key used!
HAPA UJANJAtu, hii ndio jinsi ya kugundua, kupata na kupima componets za ECU, kisha suluhisha shida hiyo. inshaAllah👇
Click Here
bonyeza HAPA
ECU cloning, duplicating or switching memory data’s,
flash memory data, EEPROM memory data, jogolize data,
HAPA UJANJA tu!
click HERE
WinOLS ni programu yenye uchawi wa kuwezesha kubadilisha, kurekebisha data iliyomo kwenye ECU.
Ina maana unaeza kutoa/kuzima hizo mifumo zenye usumbufu kwenye gari, zikiwemo IMMOBILISER (kufanya immo off). kutoa DPF, EGR, ADblue, kubadili TURBO zenye umeme, yaaani inafanya kazi nyingi kama ECU tuning, uamuzi ni wako tu🤷♂️!
Click HERE
Ujanja wa EEPROM work ni muhimu, ukitaka kumbuka niaje,
…bonyeza HAPA UJANJA tu
